HP3060 : x1/x10 Oscilloscope Probes
hp3060
Larger picture

1+   = $25.00 each
2+ = $20.00 each



The HP3060 Oscilloscope probes are the ideal companion for the DS1M12 Stingray and PS40M10 Swordfish oscilloscopes. These quality x1/x10 probes feature a input bandwidth of 60MHz and come with a full set of clips and accessories. Input impedance = 1Mohm in x1 mode and 10Mohm in x10 mode

Specification
X1
X10
Attenuation
1:1
10:1
Bandwidth
DC to 6MHz
DC to 60MHz
Rise time
58ns
5.8ns
Input Resistance
1M Ohm
10M Ohm
Input Capacitance
128pF plus oscilloscope
Approx 23pF
Working Voltage
600V DC incl Peak AC (de-rating with freq)
NOTE : These should not be used to measure voltages >=75v DC or 50v AC RMS when used in conjunction with DS1M12 or PS40M10.
For higher voltages consider using the SI-9001 ( below )
Cable Length
1.4M

SI-9001 : Differential Oscilloscope Probe X10/X100
SI9001
Larger picture

1+   = $275.00 each
 5+   = $261.25 each
10+ = $254.38 each
25+ = $247.50 each
50+ = P.O.A.






The SI-9001 Active Differential Probe converts floating signals to low voltage ground referenced signals that can be displayed safely and easily on any ground referenced oscilloscope. Ideal for use with our DS1M12 and PS40M10 oscilloscopes, SI-9001 enables users to safely make measurements of floating circuits with their oscilloscope grounded. SI-9001 is also ideal for a variety of applications - Testing 2 and 3 phase Mains Supplies, Switching Power Supply Design, Motor Drive Design, Electronic Ballast Design, CRT Display Design, Power Converter Design and Service, Power Device Evaluation

Specification

Bandwidth DC to 25MHz (-3dB)
Attenuation Ratio
1 : 10 / 100
Accuracy ± 2%
Rise time 14ns
Input impedance 4M Ohm / 5.5pF each side to ground
Input Voltage
 

Differential Range

 +/-70V(DC+Peak AC) or 70Vrms @1/10
+/-700V(DC+Peak AC) or 700Vrms @1/100

Common Mode Range

 +/-700V(DC+Peak AC) or 700Vrms @1/10 & 1/100

Absolute Max. Voltage

 +/-1400V(DC+Peak AC) or 1000Vrms CAT III @1/10 & 1/100
Output  

Swing

 +/-7V (into 2kohm load)

Offset (typical)
<+/-5mV

Noise (typical)
0.7mVrms

Source Impedance (typical)
1 ohm @1kHz, 8 ohm @1MHz
CMRR (typical) -86dB@50Hz,-66dB@20kHz
Ambient Operating Temperature -10c to 40c
Length of BNC Cable 95cm
Length of Input Leads 45cm
Power requirements 4 x AA cells or 6V / 60mA dc mains adapter

DT10 : Oscilloscope Test Leads
dt10
Larger picture

1+   = $4.95 each
 5+   = $4.70 each
10+ = $4.58 each
25+ = $4.46 each
50+ = P.O.A.






The DT10 Oscilloscope test leads are an ideal low cost companion for the DS2200C. These consist of a 1m cable with a 50ohm BNC connector at one end and a pair of sturdy crocodile ( alligator ) clips on the other.